Skip to content
  • Free freight on orders over $500
  • Authorized dealer · Full manufacturer warranty
  • Financing from 0% APR

Woodworking Machinery

Follow the stock through the shop, from rough boards to finished parts. Match each machine to the widest board, longest rip and dust volume your jobs produce.

Woodworking Machinery at a glance: Cut a cabinet side, plane a dining tabletop and collect chips from heavy milling. These are three different jobs. Lay out the longest board at both ends of each machine before assigning floor space.

Equipment types
3
Equipment types at a glance
View comparison
Buyer questions
7 answered

Side-by-side

Equipment types at a glance

EquipmentWhen to consider it
Cabinet Table SawsSize the fence and outfeed for the sheets you rip most often. A wide fence setting helps with cabinet sides only if the sheet stays supported through the cut.
Thickness PlanersMatch cutterhead width to your widest regular glue-up and look at feed speed as well as depth per pass. Multiple passes through a narrow planer can dominate a milling day.
Dust CollectorsStart at the tool with the largest chip load. The collector, duct diameter, run length and number of open branches together determine how much air reaches the machine.

Buying guide

Woodworking Machinery: what to know before you buy

Follow the stock through the shop, from rough boards to finished parts. Match each machine to the widest board, longest rip and dust volume your jobs produce.

How to choose

  • Follow one cabinet job through the shop. Choose a real cut list and trace the panels from breakdown to finished thickness. Note how often machines are reset for a different part and where stock must wait. That shows whether a wider machine, better support or shorter setups would save the most time.
  • Map the longest board. Mark the position of the workpiece before, during and after a cut or pass. Two machines can share open floor area at different times, but overlapping work paths can become a bottleneck when two operators are working.
  • Cost a complete cutting station. Include blades or cutters for the material, outfeed support, dust connections and electrical work. Check the cost and lead time for the first set of replacement wear parts as well as the machine.
  • Compare the fence on your cut list. Bring a drawer side, a narrow face-frame rail and the dimensions of your largest panel. Ask to see how the fence reads and locks at each width. A repeatable fence can save more setup time on small cabinet runs than extra table width.
  • Count passes per batch. Have the supplier work through a batch from rough thickness to finished size using your species and board width. Include the time to return boards to the infeed. Feed rate alone can make two machines look closer than they are.
  • Compare the whole duct run. Sketch the path from the collector to the farthest machine. List branches, elbows, hose lengths and the machines that run together. Request a comparison using that layout so both quotes cover the same collection points.

FAQ

Woodworking Machinery questions

What determines usable rip capacity?

Measure from the blade to the fence and compare that distance with the widest finished panel on your cut list. Leave room for the offcut and an outfeed surface.

Will a planer flatten a twisted board?

A thickness planer references the face on its bed. Prepare a flat reference face first if the stock is twisted or bowed.

Can I size a collector by motor horsepower?

Compare the airflow at the resistance of your duct run. A free-air figure alone cannot tell you what reaches a planer through elbows and flexible hose.

What should I ask to see in a demonstration?

Bring the species, sheet sizes and smallest finished parts you use most. Ask the supplier to reproduce a common cut or pass, then check the surface finish, repeatability and time to reset.

Can I use my existing dado set?

Check the manual for the permitted diameter, stack width, arbor length and matching insert. Ask which of those parts come with the saw.

How do knife changes affect downtime?

Compare the price of a complete set, the time to change or index it and whether one damaged cutting edge can be replaced individually.

What belongs in an installation quote?

Itemize ductwork, gates, flexible connections, collection bins and filter replacements. Ask the supplier to identify items excluded from the base price.

Free Shipping Over $500

Freight to the lower 48. Liftgate +$150. Pickup available on select items.

Price-Match Guarantee

We match any authorized dealer’s MAP-compliant price.

Full Manufacturer Warranty

Brand-new machines, factory-direct, with the full manufacturer warranty.

Talk to an Expert

(844) 455-4327 · Real people, Mon–Fri.